R-2024-159 - 6/27/2024 RESOLUTION NO. R-2024-159
WHEREAS, the City of Round Rock ("City") desires to purchase a battalion command
vehicle; and
WHEREAS, City is a member of the Sourcewell Cooperative, a cooperative purchasing
program; and
WHEREAS, National Auto Fleet Group is an approved vendor of the Sourcewell Cooperative;
and
WHEREAS, the City wishes to issue a purchase order to National Auto Fleet Group to
purchase said goods through Sourcewell Cooperative, Now Therefore
BE IT RESOLVED BY THE COUNCIL OF THE CITY OF ROUND ROCK,TEXAS,
That the City Manager is hereby authorized and directed to issue a purchase order to National
Auto Fleet Group for the purchase of a battalion command vehicle.
The City Council hereby finds and declares that written notice of the date, hour, place and
subject of the meeting at which this Resolution was adopted was posted and that such meeting was
open to the public as required by law at all times during which this Resolution and the subject matter
hereof were discussed, considered and formally acted upon, all as required by the Open Meetings Act,
Chapter 551, Texas Government Code, as amended.
RESOLVED this 27th day of June, 2024.
_/, A Z
CRAIGORG ayor
City of toundr, Texas
ATTEST: Ac
Mh AGAN SJKS-,rir Clerk
0112.20242:4892-5795-7575
National Auto Fleet Group
A Division of Chevrolet of Watsonville
ip 490 Auto Center Drive, Watsonville, CA 95076
(855) 289-6572 - (831 ) 480-8497 Fax
Fleet@NationalAutoFleetGroup . com
03/20/2024 Quote ID#55460NC
Marshall Reynolds
City of Round Rock
901 Luther Peterson PI
Round Rock, TX 78665
Dear Marshall Reynolds,
National Auto Fleet Group is pleased to quote the following sourced(s) for your consideration.
One(1) New/Unused (Command Access Vehicle#2 by Stonewell+ Handling$12,958.13),
Round Rock FD will transport truck to and from Stonewell installing location, each for
(1)One Unit
Contract Price $ 142,539.46
Tax(0.00%) $ 0.00
Total $ 142,539.46
-per your attached specifications:
This sourced(s) is available under the Sourcewell (Formerly known as NJPA) 060920-NAF.
Please reference this Contract Number on all Purchase Orders to National Auto Fleet Group.
Payment terms are Net 20 days after receipt of vehicle.
Thank you in advance for your consideration. Should you have any questions, please do not
hesitate to call.
Sincerely,
Jes Coo
National Fleet Manager
office(R55)2RQ_fiS77
Fax(831)480-8497
i=1Oi=OGE
� •1111111•
RAM
NOTES
Wed 3/20i2024 7:32 AM
Neil, I have spoken to our finance department, and we agree to the payment terms lined out in the quote.
Marshall
From: Neil Carroll<neil@nationalautofleetgroup.com>
Sent:Wednesday,March 20, 2024 9:25 AM
To: Marshall Reynolds<mreynolds@roundrocktexas.gov>
Subject: Re: RR#2 Update
Ili Marshall,
Following our call today, I wanted to confirm Stonewell's payment structure for the [Project Namej project.As
discussed,they require an upfront payment of one-third of the total cost,followed by another third at the project's
halfway point. The remaining balance will be due upon completion.
l"or your reference, I've included Stonewell's detailed payment terms below:
StoneweR Payment Terms:
• 1/3 of the total project cost due upon signing the agreement
• 1/3 of the total project cost due at project midpoint
• Remaining balance due upon project completion
Please note: Stonewell reserves the right to pursue legal action for late payments,with all associated legal fees being
the responsibility of the client. Additionally,the project will not be considered complete or usable witil full payment is
received.
Please let me know if your agency accepts these payment terms. I'm happy to answer any questions you may have.
'Thanks.
Neil Carroll Director of Sales
COMMAND ACCESS VEHICLE #2
ROUND ROCK TEXAS
FIRE DEPARTMENT
Marshall Reynolds
901 Luther Peterson
Round Rock Texas, 78664
512-218-5571
mreynolds@roundrocktexas.gov
Lou Sposito
625 Sills Road
Genoa NY 13071
315-497-3512
Isposito@stoneweIIbodies.com
Date 1-26-2024
Price
$129,58133
1
STONEWEGL COMPANY HISTORY
Stonewall Bodies was founded in 1994 out of the necessity to work smarter and not harder. The company was
started by a farrier looking to shoe his horses without the trouble of constantly loading and unloading a pickup
truck with all his tools of the trade. After carefully considering how to make a truck body that would be light,
provide protection from the elements,easy to organize and last for many years,the Stonewell Body was created.
Today, Stonewell has grown to service three primary industries, all of which require a lightweight and efficient
design. The primary industries serviced by Stonewell include Farriers and mobile veterinarians, emergency
services vehicles and the building trades. The common thread among these three industries hinges on the need
of efficient access to the truck body so they can access and depart the vehicle as quickly as possible.
Stonewell now employs 37 craftsmen who are experts in the field of fabrication as well as having significant
application experience in the field of EMS and Farrier. Our team is comprised of farriers. EMT's,volunteer Fire
Chiefs and assistant Chiefs. These craftspeople bring their passion and practical experience with theta as they
work to build outstanding truck bodies.
Coupled with experts in fabrication, Stonewell has made significant investments in productions capabilities. Our
bodies and fabricated solutions are designed using the latest CAI), and modeling,software coupled to fully CNC
processing equipment. Our metal cutting is primarily achieved through a new Mitsubishi Laser, HAAS milling
machines or other very prices machine-tools. We have invested in our infrastructure as well as equipment and
are confident we can design, weld and manufacture to the exact specifications we develop.
Over the last several decades, Stonewell has evolved to be a market leader with a robust complement of tools
needed to solve customer problems. We continually work to solve application problems and stand behind the
products that we produce. We look forward to the possibility of working with you and hope you consider
Stonewell Rodics for your next design need.
TERMS OF PAYMENT-DIVIDED IN ONE THIRD INCREMENTS
The terms of this purchase shall be(Radio items) 1/3rd of the body purchase price upon signing of the purchase
agreement and 1/3rd at the midpoint of construction. The balance shall be paid upon completion of the specified vehicle.
If payment is not made and Stonewell must pursue legal remedies,all legal expenses shall be the responsibility of the
purchaser. The vehicle shall not be put in service until full payment is paid to the manufacturer.
2
ACNE:ENIE NT OF SALE FOR C(N'INIAND ACCESS YM HICI E
THiS AGREEMENT is made butwcrn ltonewell Bodies and Machine Inc.(Stonewell)and.
Legal Name of Buyer Marshall Reynolds
Address 901 Luther Pv'terson,Round Rock Tc=as,79664
Phone Number c 12-21 R-5571
ACCEVrA\CF.:
Stuneweli agrees to sell,and Buyer agrees to purchase(quantity)_Command Access Vchicle(s i descrihcd m the SMilicauons nicxxporated as Exhibit
A of this c011trac4 as may be amended in writing,and the eyuiptrtent listed herein,all in accordance with the terms and conditions set forth herein.
This offer is valid for 30 days from 1-_6-2024 anti shall expire on 2-27-2024.
1. DELIVERV SCHEDIIISA
The Command Access Vehicle shall he ready for transport in approximately I8o days after delivery of the chassis ul Stoncwcll assembly line. This
tirric frame Is subject to extension due to changes made by Buyer or in accordance with Secito is 4 or 10.11.12 below.
2. PRIC't''
Huyci shall pay Stonewell(3tw11c,a-sf4,;h-e Int the pur.haac P11"lues the installation vtdie
Cumrnand Access Vehicle in the sum of $129,581.33 U.S.Dollars
This purchase price ei1at1ft faxes.Responsibility to pay taxes are with the hu%er.
Any applicable taxes not speclllcally maed shove will be paid by the Buyer directly of will lie added to the purchase ptive and paid by Buyer. It
Buyer claims exemption front any tax,[luycr agnees to promptly furnish the applicable cxonpuon cert)ficatie(s)and to Indemnity and hold harmless
Stoncw'cll Bodies& Machin Inc harmless from any such tar interest or petwlty,which rnay at any,time be assessed against Stonewell Bodies Rc
Machine Ittc.ws a result of this transacuon
I. TERMS OF PA1-HENT SHALL.BE:
Due ta(xln signing:Radio gear-1:3 S 35,928.33+21796.33 a 57,724.66
Due upon video conference inspectitin alter-'9()days of build I .S35,928-1.1
[see upon completion and video or in-person lat voter cus9l inspecuun prior to shipping—...$35,92833
Applicable method of payment for retllaining balance due.(:heck,.w w ire transfer.
In the event of a dtsputc,Stonewell Bodies ah Jl have the right to collect,Item the purchaser,re -Kivable costs and necessary disbursemenls and
atiomcy's fees uxLurrr l in enforcing this agreement.The vehicle shall not be(tut in service until full payment is paid to the
manufacturer.
4. CONTiNGFNC IL%
Stonewell will not be liable for any delay, factum to make dehvrry.or other default d uc to strikes or labor unrest, war,siert.federal, btate or local
governint" action,Pyre.fkxA,or other disaster or acts of God.accidents,brcakduwn of machinery,lack of or inability to obtain materials,parts or
,upplies,or any other causes or circumstances bcytad the rcasonahle control of these emiues which prevent or hiruler the manufacture and ur dclivcn
of the Command Access Vehicle
S. %ARR1*L1%-l l
Sion-ac(l provides a linut t!warranty on new Cownwnd Access Vehicle of its own manul'ae'ture in accordance with the warranty terve set forth in the
�-Nctncsicmas provwed.LAltvi t I Hh Lx ItNI PRulltEilIEll BY LAW,SIONEWELL MAKES NO MEIEiR WARRANTY,EXPRESS OR
-4"LIUI%,INCLV LIIriti r1 IF IMr`Liva?N'.1riR Ail r au.nr'h1u1tcl loss,-.olt.tI Y 011 1 I Ir X431,011L A 1'Aft ricuL.Afl rvKrO:3t.TI li:rtt'.AM
NO WAR WHICH F_XTT- B[iYl�Nl) THE FACE HEREOF. SE[ SCPAKATL WARRANTY SfAI'EMF.Ni'tSt FUR l'UMPLf'fl
INFORMATEON.This warranty starts upon placing the%chicks in service not to exceed 6 nwntlul atter deliver.
3
G. DISCLAIMER OF CONSEOUENTLAL DAMAGES:
Stanwell EXPRESSLY DISCLAIMS ANY LIABILI IN FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES WHICH MAY BE SUSTAINED
BY BUYER.INCLUDING BUT NOT LIMITED TO THOSE ARISING FROM THE USE,INABILITY TO USE.MAIN TENANCEOR REPAIR Of
THE COMMAND ACCESS VEHICLE,WHMIER UNDER THEORIES OF BREACH Of EXPRESS OR IMPLIED WARRANTY,NEGUGENCE.
STRIC`r LIABILI-IT,OR OTHERWISE.
7. CANCELLATION:
Thh contract is not subject to cancellation by Buyer,unless for material breach by Stonewell Rodies.except upon payment to seller of reasonahle
cancellation charges,which shall tape into account expenscx,already incurred and cwnmitntent%made by wlkf and seller's antietpawd pruftt
S. ENTIRE AGREEMENT,AMENDMENTS
1 his contrera,including its appendices,embodies the entire mxfetstanding between the parties relating to the subtest mailer contained herein and mages
all prior discussions and agreements birmven them.No agent or representative of Stonewell hers authority fo make any represetttatioas statements.
warranties or agreemcntc not herein expressed.All nutdiftcatioos or amendments of this contract.includinS the appenlicca,and Change Orders.imist
he in utiting signet h%an authorized representative of each of the patties hereto.
9. SEVERABILITY
If any provision hercuf shall for any reason be held to be invalid,illegal ox unenf'urcx able in any respect,such invalidity,illegality or unenforceability
shall not alTmt any other provision,and this contract shall be c:onstnt xd as if the invalid,illegal or unwillki :eable provision had never been contained in
it.unless to do so clearly uegates the overall intent or purpose of the panics in entering into this contract
10. CiLANGES LN CQ?t"MRC1AI.SPECIFICATIONS
Specifications for all amuncrciai cuntponcnts of the Command Access Vehicle,tmanufactured by companies other than Stonewell are wbiactto change
without notice Specifications fix such compceicnts%ill be as available at the time of nwnulacturc of the 0)mt:tanJ Auras Vehicle.Ssomwell&hail not
be IiaMe for any specification deviations Goin the original"tract specifications on sua components trade by their original manufacturer.
11. CHANGES IN REGUI,ATIONStiNDUSI RY STANDARDS:
The Purchase Price is subj"t to adjustment fix chaages to the Coatmand Acc gas Vehicle necessitated by changes in applicable government rcgulatkkma
(such as FMVSS or emissions regulations),industry standards(such as NEPA standards),reptaccrnmnt of discontinued models or compeounts from
vendors,or Geight charges.Buyer is rcspunsihfe for any cost increases due w such changes beyond Stonewell Bodies and Stonewell Bodies&,Machine
Inc.s contml.
12. CHANGE ORDERS
C'bangcA in the build cuumit:t may be submitted to Stnxxs►ell.These changes must be in writing sad when trtx mry,drawings ntay be n:oiuircd.
Depcn&nt on%here in the build process the CAV is,the ehaw order tray be accepted or rejected by Slone%tll.The cost of the change will be added
onto the total cost of the CAV. This new price ttwcat be Wpr--cd tad agreed to in writing by the purchaur.While change onkrs are being processed,
the cumpietion date shall be extended ac.vxding to the days spent processing the change order as well as the time needed to complete the
changes.
4
IN WITNESS WHBREOF, Buyer and Sumeuvil Rud cs & Machine Inc. have paused this agrccmeat to be ctwuted by their duly authori�uj
repret:ntatives this day of:
PURCHASER: Round Rock fire Department
Print Name:
Signature!
Title:
Date:
This contract h not at valid and binding obligation until approred.dated and ciecuted by Munek%eli Rodies tf.Machine Inc. Inc.
ACCEPTED AND APPROVED
SHLLER: Slonewell Bodies&Machine,Inc.
Print Name:
Signature: --
rile'
Date:
CONSTRUCTION PERIOD
As noted in these specifications, each bidder shall state the estimated delivery time in calendar days. Keep in
mind that the purchaser may elect to ave and the contract based on delivery as well as price and conformance with
the specifications.
The contract period for this apparatus shall be a maximum of 190 calendar days after recciDt of the chassis.
The successful bidder shall not be responsible ibr delays in delivery due to strikes,acts of God,failure of suppliers
to deliver,chassis shortage and other reasons beyond the reasonable control of the builder.
Should the bidder be unable to comply with the proposed delivery date, the purchaser shall be notified
immediately with the reasons for non-compliance. Failure to meet the stated delivery may constitute a breech of
contract.
PRE-CONSTRUCTION MEETING
A pre-construction meeting shall be conducted via a Webcast.
Warrant},Apparatus Section,parts and labor,One t l I Year(Q)
5
UNE ll) YEAR PARTS & LABOR WARILANTY
Stonewell Bodies& Machine Inc.. SWBM Limited Warranty Coverage. General parts and labor warranty for the body,
integral components, materials, and workmanship are warranted against defects and failure for one(1) year on parts and
labor.
Components purchased by SWBM from suppliers are subject to the warranties provided by those suppliers.Warranty period
commences from the in-service date for the body.The body must be used only for its intended purpose.The body must be
maintained and serviced according to the guidelines in the supplied documents.
Exclusions: This warranty applies only to the S WHM manufactured body and its integral components and excludes options
and accessories,which are covered by separate vendor specific warranties.The warranty is valid only when the body is used
for its intended purpose. Warranty does nut apply to any product or component that has been overloaded.altered,abused,
misused,or damaged by impact or collision. This warranty is not transferable.
Warranty repairs performed by SWBM or its authorized agents: warranty repairs shall be performed at an SWBM facility
or at an authorized distributor. SWBM may,at its discretion.pick up and return the vehicle to the owner's location or may
request that the owner deliver the vehicle to the repair site.
Warranty repairs performed by non-SWBM Entities: SWBM may authorize a third party to perform warranty repairs.
Any such decision will be based on type of repair,distance to the nearest approved SWAM repair site,and urgency of the
repair. SWBM must provide written authorization and permission before a non-SWBM entity begins repair or replacement
of components. Warranty claims for unauthorized and unsubstantiated work may be denied.
Peripheral, incidental, and consequential damages and claims: The SWBM limited warranty does not apply to damage
and failure resulting from misuse,abuse,neglect,accident,improper customer/distributor installation,lack of maintenance,
or natural events.
Any modifications by the buyer or any third party, without the prior written consent of SWHM, may void this warranty.
operating conditions,or applications not made known to or contemplated by SWAM at the time of delivery to the buyer
may also void this warranty. Damages resulting from any other abnormal operation will not be covered by this warranty.
Normal maintenance,wear,and consumable items such as light bulbs are not covered under this warranty.
SWBM will not reimburse for lost time,business,or business opportunity,or for any loss of use related to warranty claims.
SWBM will not provide or pay for the use of a rental vehicle,equipment,or tools while warranty work is performed. SW13M
will not reimburse for equipment or tools that are damaged,lost,or missing in conjunction with a warranty claim. SWBM
is not responsible for,and will not reimburse for mileage, fuel,and wear incurred in the process of driving the vehicle to a
repair site or delivery to the end user location,nor for lost time incurred by an owner delivering and picking up a vehicle or
associated components.
This limited warranty is the sole and exclusive remedy for oefmtive pruducus m.uutr&Aurcd and.lor installed by SWBM.
S
HOW TO OBTAIN WARRANTY SERVICE FROM STnyca,«I U.BODIES& ►14CHIVF Vcf
Making an appointment for warranty service at an SWBM facility or authorized repair site:
1. Call the SWBM location where your truck was built.
2. Discuss the problem with the warranty representative to determine resolution and repair schedule.
Requesting authorization to perform warranty work:
1. Obtain the following information: All of the information requested in item#2 above.
a)Documented photographs for any physical damage.(paint.dents,etc.)
b)Inspection notes by SWAM personnel or a third party representing SWBM if necessary.
2. Call the SWBM location where Your truck was built. Discuss the problem with the warranty representative to determine
coverage and repair method.
3.The representative will grant permission to perform repairs if approved.
4. IMPORTANT! The representative must issue a Returned Goods Authorization(RGA)number.
5. Defective parts must be returned freight prepaid to SWBM within seven days.
6. if the affected component was purchased from a non-SWBM supplier,please allow extra time for SWBM to contact and
work with the supplier.
Stonewell Bodies & Machine Inc. reserves the right to deny any warranty if proper procedures arc not followed. Proper
documentation, including photos, must be provided for SWBM to validate and approve any claim submitted after repairs
are done by a third party.
FIVE(5) YEAR STRUCTURAL BODY WARRANTY
Stonewelt Bodies & Machine Inc. SWBM Limited Warranty Coverage: the structural integrity of the body, integral
components,materials,and workmanship are warranted against defects and failure for five(5)years,with 100%parts and
labor coverage. This warranty is in addition to the standard parts and labor warranty attached for the entire body and
components.
Components purchased by SWBM from suppliers are subject to the warranties provided by those suppliers.Warranty period
cornmences from the in-service date for the body. The body must be used only for its intended purpose. The body roust be
maintainer and serviced acenrding to the gividelin" in the glIp+lim a neuments
hxclusioms: This warranty applies only to the SWBM manufactured body and its integral components and excludes options
and accessories,which are covered by separate vendor specific warranties.The warranty is valid only when the body is used
7
for its intended purpose. Warmly does not apply to any product or component that has been overloaded,altered,abused,
misused,or damaged by impact or collision. This warranty is not transferable.
Warranty repairs performed by SWBM or its authorized agents: warranty repairs shall be performed at an SWBM facility
or at an authorized distributor. SWBM lav, at its discretion, pick up and return the vehicle to the owner's location or may
request that the owner dcliver the vehicle to the repair site.
Warranty repairs performed by non-SWBM Entities: SWBM may authorize a third party to perform warranty repairs.
Any such decision will be based on type of repair, distance to the nearest approved SWBM repair site,and urgency of the
repair. SWAM must provide written authorization and permission before a non-SWBM entity begins repair or replacement
of components. Warranty claims for unauthorized and unsubstantiated wort:may be denied.
Peripheral, incidental,and consequential damages and claims: The SWBM limited warranty does not apply to damage
and failure resulting from misuse,abuse,neglect,accident,improper customer/distributor installation, lack of maintenance.
or natural events.
Any modifications by the buyer or any third party, without the prior written consent of SA'BM, may void this warranty.
Operating conditions, or applications not made known to or contemplated by SWBM at the time of delivery to the buyer
may also void this warranty. Damages resulting from any other abnormal operation will not be covered by this warranty.
Normal maintenance,wear,and consumable items are not covered under this warranty.
SWBM will not reimburse for lost time,business,or business opportunity,or for any loss of use related to warranty claim.
SARM will not provide or pay for the use of a rental vehicle,equipment,or tools while warranty worm is performed. SWHM
will not reimburse for equipment or tools that are damaged,lost,or missing in conjunction with a warranty claim. SWAM
is not responsible for,and will not reimburse for mileage, fuel, and wear incurred in the process of driving the vehicle to a
repair site or delivery to the end user location,nor for lost time incurred by an owner delivering and picking up a vehicle or
associated components.
This limited warranty is the sole and exclusive remedy for defective products manufactured and or installed by SWBM.
PAINT WARRANTV
The PPG Comttk:rtaal Paint Performance Warranty covers the vehicle refinished with specified and approved
products for a period of three (3), years beginning the day the: vehicle is delivered to the Customer ,' dealer.
warranty provides coverage for the following items:
a) Peeling or delamination of the topcoat and or other layers of paint
b)Cracking,checking
C) Loss of gloss Caused by cracking, checking, or hazing
8
PAINT WARRANTY EXCLUSIONS
Paint deterioration, caused by blisters or other film degradation due to rust or corrosion originating from the
substrate. Hazing, chalking or loss of gloss caused by improper care,abrasive polishes, cleaning agents,heavy
duty pressure washing. or aggressive mechanical wash systems. Paint deterioration caused by abuse, scratches,
chips, gloss reduction, accidents, acid rain, chemical fall-out or acts of nature. Failures on finishes due to
inadequate film builds. Failures due to improper cleaning or surface preparation or failure to allow the product
instructions.
Claims presented without proper warranty documentation.
"AS BUILT" «7RING DIAGRAM
The manufacturer shall provide one (1) "as built" wiring schematic for the electrical components and the wiring
system. These diagrams shall be in a notebook type binder,with reference tabs if needed.
CHASSIS SPECIFICATIONS
COMMERCIAL,CHASSIS
The chassis shall be a new, unused commercial chassis drop shipped to the apparatus body ntanufacturees
production facility. Stonewell shall conduct the pre-delivery inspection.
CHASSIS SPECIFICATIONS
One(1)CHEVROLET 2500,Pick Up Truck, four-wheel drive, single rear wheels, four(4)door crew cab.
ADDITIONAL BATTERY UPGRADE
Two(2)Batteries in CAV body 31 Series Scrcw Top post
FROST BUMPER— BRL-SH GUARD
1 hrottle Down,MS 13093.Painted Cheery Red
REAR Ht:,N1PLR - DIAMOND PLATE
An aluminum bumper that is full width of the body shall be installed. The bumper shall be constructed of formed
rectangular aluminum sheet and al►all be fully welded. The buinper shall be mounted to the chaaaia frame and
Snall [louse tilt!OL'M bat;k uEi TLc buinyc:t vvctiay alcurl Uv Dicun011A Plata.
Painted. Chevy Red Same as Pickup
9
REAR MUD FLAPS
Black mud flaps with the stainless-steel logo shall be installed behind the rear wheels.
CAB STEPS
Ranch Hand RHD-RHC191C6B6S Painted Chevy Red Sane as Truck
CENTER CONSOLES
Plastix Plus Center Console
Plastix Plus.pptexas.com 281-469-3451
Wired Hot
COMPUTER DOCKING MOUNTS
Havis Post and Docking
Steel I-pad mount shall be fasted to the center console The mount shall have the following features:
Mount for Wad in Ccnter Console and Command Pack
Same I pad mounting system in the rear command pack
BODY AND COMPARTMENT SPECIFI CA TIONS
Stonewell Command Access Vehicle
(CAV)
Bodv Specification
('A%': 90"L x 76"W x CAB HEIGHT.FULL DOOR
The CAV body shall be suited to a Short Bed Pick Up Truck. The body shall incorporatc Ful I Length Doom.
GENERAL OVERVIEW
The Stonewell Command Access Vehicle(CAV)is a multi-purpose aluminum truck body intended to replace
factory-made pick-up truck beds installed by manufacturers such as Ford, GM and Fiat Chrysler. Once a
factory installed bed is removed, the CAV body will be mounted to the frame rails of the chassis and a provide
an enclosed structure to store, transport or secure items as needed.
The CAV body is manufactured from an aluminum sub-structure and frame that is skinned with aircraft grade
aluminum panels thus enclosing the structure. Three(3)main doors shall provide access to the upper section
I frame)of the CAV body,and depending on interior construction,shall provide visibility to the entire above-
frame comnartment. The CAV is hi¢h1v versatile in its intended application and with an interior designed to
address the specific needs of the user.
10
In emergency services applications,the CAV can he configured with NFPA-like lighting. Interior and exterior
lighting shall be added per customer specifications. Additionally,paint, graphics, lettering,chevrons and
striping can be added to support NFPA standards and customer needs.
hRAME CONSTRUCIIJON
The frame of the CAV shall be considered the txxly structure coming directly in contact with the vehicle chassis
though isolated via our mounting system. The frame structure shall be M iG welded and comprised of extruded
aluminum tubing made of 6061 x .125" material, hardened to T-6 specifications. At no time shall the frame of
the CAV come in direct contact with the chassis of the vehicle. The frame shall be welded in a proprietary
pattern to maximize strength and minimize body flexing. All tubing shall be cut via CNC controlled saw to
ensure precise tube section length. Welding of the tubes shall be done in a rotary fixture to minimize tube
warpage:and ensure:proper fit-up for welding. Butt-welding of tubes will include end-chamfering of tube
lengths to ensure weld penetration. Additionally, welds shall be no smaller than 3/8"and no larger than 'ii"and
shall be welded on no few than two sides. Where allowable based on construction method,all 4 sides of the
tube shall be welded. "Dube sides requiring skinning shall have welds ground smooth to minimize skin warpage
or deflection.
HOOP CONSTRUCTION
Similar to frame construction, the hoop section of the:CAV shall be considered the vertical structure mated to
the frame and rising vertically to form the storage compartment. The hoop structure shall be MIG welded and
comprised of extruded aluminum tubing made of 6061 x .125" material, hardened to T-6 specifications. All 4
sides of the tube shall be welded to its counterpart. At no time shall the hoop of the CAV come in direct contact
with the chassis of the vehicle. The hoop shall be welded in a proprietary pattern to maximize strength and
minimize flexing. All tubing shall be cut via CNC controlled saw to ensure precise tube section length and cut
angle. Welding of the tubes shall be done on a rotary fixture to minimize tube warpage and ensure proper fit-up
for welding. But-welding of tubes will include end-chamfering to ensure weld penetration and angle
correctness. Additionally, welds shall be no smaller than 3/8" and no larger than '..Z" and shall be welded on no
fewer than(4)four sides. Where allowable,based on construction method, all 4 sides of the tube shall be
welded. Tube sides requiring skinning shall have welds ground smooth to minimize skin warpage or deflection.
Water"gutters"shall be installed on the side door outer most frame members. 'l'hese gutters shall enable water
to be channeled off the roof surface and follow a path to leave the Ixxiy without entering the main storage
compartment.
t'ROTt:CTIVE CUVLKING — FRONT BODY
The entire front of the apparatus body shall have a protective covering installed. The covering shall be constructed
of bright .100" aluminum tread plate material.
11
ROOF CONSTRUCTION
The portion of the hoop considered the roof of the compartment shall be framed with 6061 x .125" material,
hardened to T-6 specifications. The same welding practice as used in the frame and hoop manufacturing
process shall be used to construct the roof. The exterior portion of the roof shall be lined with 5052 x .060"
aluminum on the exterior. The exterior skin shall be bonded to the roof frame utilizing an aluminum adhesive,
3M brand VIiB double sided tape and zinc coated mechanical fasteners. Any mechanical faster that is exposed
to the elements shall be covered with silicone to ensure a water proof seal. To minimize condensation in the
compartment, R-15 foam board insulation shall he installed between the roof cross-members and encased
between the roof skin and an interior skin (ceiling). To complete the roof section, an interior skin of 5052 x
.040" aluminum shall be installed on the"ceiling" portion of the root. This skin shall form the interior ceiling.
Gussets shall be welded in the corner joints that connect the roof to the hoops. The gussets shall be stitch
welded to minimize warpage of either the roof, hoop or gusset.
SIDE DOOR CONSTRUCTION
Construction of the CAV side doors shall consist of an interior frame with laminated skin. I he exterior portion
of the door shall be constructed from 5052 x .090" aluminum. The exterior skin shall be bonded to(lie door
frame utilizing an aluminum adhesive applied under pressure,and 3M brand Vi113 double sided tape.
Mechanical fasteners shall not be used to fasten the skin to the frame. The frame and door skin shall be angled
in such as way as to contour to the shape of the track. -D" seal shall be applied to the perimeter of the door to
create a waterproof seal and a
rain gutter shall be formed to channel water away from the door opening.
REAR DOOR CONSTRUCTION
Construction of the CAV rear door shall consist of an interior frame with laminated skin. The exterior portion
of the door shall be constructed from 5052 x .090" aluminum. The exterior skin shall be bonded to the door
frame utilizing an aluminum adhesive applied under pressure, and 3M brand VHH double sided tape.
Mechanical fasteners shall not be used to fasten the skin to the frame. The frame and door skin shall be
mounted to the roof of the body using a stainless steel hinge, with a pin diameter of no less than .125". "D"
seal shall be applied to the perimeter of the door to create a waterproof seal.
12
SIDE DOOR HINGES
The side doors of the CAV unit shall be comiected to the roof of
the body using a proprietary interlocking sliding j hinge. The
hinge shall be:water proof and shall run full length of the roof
surface to evenly disperse the weight of the door. A piano style
hinge shall not be used to connect the doors to the roof. Please see an illustration of the roof hinge sections.
The hinge shall be connected to the roof and door section and form a water tight union that can slide forward,
and aft,to accommodate light contact should the door be struck on the leading or trailing edge-while in the
open position. Stainless steel rivets shall be used to connect the hinge to the door and self tapping screws shall
he used to connect the female portion of the hinge to the rtof. A sealant shall he applied between the roof and
hinge to create a water barrier. Inch self tapping screw shall have a factory installed rubber washer to further
protect from water entering the main body.
REAR DOOR RING
The rear door hinge shall be of a piano style design and shall he stainless steel. The hinge pin diameter shall be
no less than .166". 1 o ensure a water tight connection between the door and the body,the hinge shall be
covered with a rubber membrane that is flexible and durable. Additionally, any fasteners used to connect the
Jour to the roof shall be encased in silicone that is applied under power.
BODY NIOUNTING
The body mounting system shall consist of an UHMWPE contact strip and aluminum extrusion. The aluminutn
extrusion will be welded to the CAV frame while the UHMWPF contact strip shall be in contact with the
chassis frame and retained be the extrusion. This mounting method prevents electrolysis and enables body and
chassis flexing. A coil spring and bold system shall be used to secure the holy to the chassis.
CONIPARTMENII FLOOR CONSTRUCTION
The compartment floors shall be .125" #5052-1-132 aluminum with a "lip free" and sweep out construction,
which shall permit easy cleaning of the compartment. A DA finish shall be applied.
DOOR HANDLES
Eberhard stainless steel door handles shall be used on all (3)three compartment doors. Side doors shall be
fastened using a slam latch method, while the back door shall utilize a rotary latch and cable system. All door
latch points must be adjustable without the need to Cully remove the latch. No plastic shalt be www in any doui
handle, latch or striker.
• 13
FASTNERS
Fasteners are to be stainless steel unless used in roof surfaces or for interior component mounting.
FUEL FILL ACCESS—LEFT SIDE
A Cast Products model#FG2103 fuel fill cover shall be installed on left side of the wheel well area. The cover
shall be custom made of polished aluminum and shall be vertically hinged on the forward side.
ELECTRICAL EN CLOSURES
Two(2)electrical wiring enclosures for the 12 volt wiring shall be installed in a rear body compartment with
removable panel. Easy access to electrical connections is required.
12 VOLT POWER SOURCE-DUAL OUTLET
One (1) dual 12-volt plug-in utility power connection rated at 20 amps shall be provided at rear of CAV body
mounted in the vertical tail panel. Model Waytek 78035.
F;LFCCRICAI WIRIN ` A'ND HARNESS
The body shall be pre-wired with various electrical harnesses and conduits. The 12 volt electrical wiring shall
be function coded and enclosed in split loom conduits, suitably secured and protected against beat and physical
damage. All wiring shall be sized according to circuit load. All connections are to be of a crimp type with heat
shrink insulator where required.
The electrical system shall be divided into separate harnesses. The individual harness shall be connected to the
electrical box with Deutsch quick connectors. The apparatus lighting shall be protected by automatic circuit
breakers and/or relays. The electrical power to all apparatus lighting and accessories shall be supplied by an
ignition activated solenoid.
IDENTIFICATION LIGHTS
All LED identification lights shall be installed on the vehicle as required by applicable DOT highway
regulations.
Red- B& D Sides, lower rear end of body
OPEN DOOR MARKER .I HT
A '/:' LED marker light shall be installed in the perimeter of the CAV driver and passenger side door frame
corners. The light shall automatically tilm on when the dfu-w is opened to alert nrteratnrc of the door In afinn A
total of 2 lights shall be installed in each door. The locations shall bc:
14 •
Amber in the leading outemiost door frame
Red in the outermost rear of the door frame
OPEN DOOR CONSPICUETY TAPE,
Each side doors' outer frame corner shall be wrapped with red and silver conspicuity tape. The tape shall
extend approximately 12" from the outermost corner.
DOT COMPLIANT REFLECTORS
Reflectors shall be applied to the body to ensure compliance to all State and Federal regulations.
LICENSE PLATE BRACKET
A license plate bracket with LED light shall be provided at the rear of the apparatus, unless otherwise specified
by the department.
INTERIOR COMPARTMENT FINISH
The interior bulkhead wall, floor and ceiling surfaced;of the body compartments shall be unpainted aluminum.
The deck shall be an aluminum DA finish while the bulkhead shall be mill finish. Care shall be taken in the
manufacturing process to minimize blemishes. All joints and seams will be sealed with TremPro 644 RTV
silicone tined metallic silver.
WHEEL WELL LIFERS
Wheel well liners designed to protect the body from impact resulting from road debris thrown by the tires shall
be installed.The wheel well shall be provided with aluminum fender liners that shall be formed so as to
eliminate pockets that might trap and collect road dirt.
UNDER BODY COMPARTMENTS -11RIVER& PASSENGER
Two(2)under body equipment storage compartments shall be installed under the body surface, one each side of
the apparatus. The dimensions shall be approximately: 22" wide, 12" high, and 10" deep. The compartments
shall be constructed of.90" aluminum on all exterior surfaces. Each compartment shall be equipped with a
hinged drop-down door. The chassis will have a retaining cable that prevents the door from dropping past
horizontal.
15
CAN' DRIVER SIDE INTERIOR
Refer tci Drawing
CAV PASSENGER SIDE INTERIOR
Refer to Drawing
CAV REAR INTERIOR
Refer to Drawing
CAV REAR CAB CABINET BACKSEAT
Refer Qi Drawing
REAR WHEIF:L FENDERE7'TkS
The wheel well openings shall be of sufficient opening to permit the utilization of tire chains or other traction
devices. Polished aluminum Fenderettes shall be installed at each rear wheel opening. The Fenderettes shall be
positioned outside of the wheel well panel to cover the tire area that extends past the body. The Fenderettes shall
be secured with threaded aluminum hardware and spaced approximately 3/16" of an inch away from the wheel
well panel.
LOW VOLTAGE ELECTRICAL SPE IFICATIOAS
BATTERY JUMP START SYSTEM
The apparatus shall have provisions for connecting jumper cables. The installation shall be internally wired to
the 12-volt chassis batteries and terminate with a female receptacle and weather resistant cover. The juniper
cables shall be 12' long with a male plug on one end to connect to the plug-in receptacle. The other end shall be
configured with a red,positive spring-loaded clamp and black,negative spring-loaded clamp, with identification
label shall he installed. Location of the receptacle shall be :
12 VOLT ELECTRICAL SPECIFICATIONS- FULL INSTALLATION
The following describes the low voltage electrical system on the apparatus including all panels, electrical
components, switches, wiring harnesses and other electrical components. The apparatus manufacturer shall
conform to the latest Federal DOT standards, current automotive electrical system standards and the applicable
requirements of the NEPA.
Wiring shall be stranded copper or copprr alloy conductors of a gaugc tatetl to um z y 125 peit;eni,OfOIC IrtaXlttlUtn
Lurteni fur wl►ich Ute circuit is protected. Voltage drops shalt not exceed it)percent to all wiring from the power
source to the device. The wiring and wiring harness and insulation shall be in conformance to applicable SAE
and NFPA standards.The wiring harness shall conform to SAE J-1128 with GXL temperature properties. Exposed
16
wiring shall be run in a loom with a minimum 289 degree Fahrenheit rating. Wiring looms shall he properly
supported and attached to body members.Electrical conductors shall be constructed in accordance with applicable
SAE standards.except when good engineering practice requires special construction.
All wiring connections and terminations shall provide positive mechanical and electrical connections and be
installed in accordance with the device manufacturer's instructions. When wiring passes through metal panels,
electrical connections shall be via mechanical fasteners and rubber grommets.
Wiring between cab and body shall be split using Deutsche type connectors or enclosed in a terminal junction
panel allowing body removal with minimal impact on the apparatus electrical system.Connections shall be crimp-
type with heat shrink tubing with insulated shanks to resist moisture and foreign debris such as grease and road
grime. Weather resistant connectors shall he provided.throughout the system.
Llectrical junction or terminal boxes shall be weather resistant and located away from water spray conditions.
When required,automatic reset breakers and relays shall be housed in the main body junction panel.
There shall be no exposed electrical cabling,harnesses, or terminal connections located in compartments, unless
enclosed in an electrical junction box or covered with a removable elec-tneal panel. Wiring shall be secured in
place and protected against heat,liquid contaminants and damage and shall be uniquely identified by color coding
or permanent marking and identified on a reference chart or electrical wiring schematic per requirements of
applicable NFPA standards.
Low voltage overcurrent protective devices shall be provided for the electrical circuits. The devices shall be
accessible and located in required terminal connection locations or weather resistant enclosures. Qvercurrent
protection devices shall be automatic reset type suitable for electrical equipment and meet SAE standards. All
electrical equipment, switches, relays, terminals, and connectors shall have a direct current rating of 125 percent
of maximum current for which the circuit is protected. Electro-magnetic interference suppression shall be
provided in the system as required in applicable SAE standards.
• The electrical system shall include the following:
• Electrical terminals in weather exposed areas shall have a non-conductive grease or spray applied. All
terminal plugs located outside of the cab or body shall he treated with a corrosion preventative compound.
• All electrical wiring shall be placed in a protective loom or be harnessed.
• Exposed connections shall be protected by heat shrink material and sealed connectors.
• Large fender washers shall be used when fastening equipment to the underside of the cab roof and all
holes made in the roof shall be caulked with silicone.
• Mccuic:al wrnponcnts installed in exposed areas shall be mounted in a manner that will not allow moisture
to accumulate inside.
17
• A coil of wire must be provided behind an electrical appliance to allow them to be pulled away from the
mounting area for inspection and service work.
• All lights in a weather exposed area that have their sockets shall have corrosion preventative compound
added to the socket terminal area.
• Warning lights shall be switched in the chassis cab with labeled rocker type switches located in an
accessible location. Individual rocker switches shall be provided only for warning lights provided
exceeding the minimum level of warning lights in either the stationary or moving modes. All electrical
equipment switches shall be appropriately identified as to their function and mounted on a switch panel
mounted in the cab convenient to the operator. For easy nighttime operation, an integral indicator light
shall be provided to indicate when a circuit is energized.
A single warning light switch shall activate all required warning lights. This switch will allow the vehicle to
respond to an emergency"calling for the right of way". When the parking brake is activated,a"blocking the right
of way" system shall be automatically activated per NFPA requirements. "Clear" warning lights shall he
automatically shed on actuation of parking brake.
Upon completion of the vehicle and prior to delivery, the apparatus shall be electrically tested and the electrical
testing,certifications,and test results shall be submitted with delivery documentation per requirements of NFPA.
Fie boxes at Center Console and in the Rear Command pack
ELECTRIC DOOR LOCKS
Remote actuated door locks. Activates all large body-doors with key fob. Includes installation.
USB Port,Kussmaul,in Center Console(2)
USBPORT
Two Kussmaul model 091-219-4.4.2 Amp USB ports shall be installed in the rear command pack. A
protective cover shall seal the input ports.
KNOX BOX INSTALLATION
Wire only. Location Passenger side tipper shelf. THD
120 VOLT SHORE POWER RECEPTACLE
A Kussmaul model 091-55-20-120 20 amp "auto-eject" shore power receptacle shall be provided with hinged
weatherproof uovcr and an cut:lusurc fut prutet;tiutt L'txn toad dirt and datuage The short~power plug shall be
"ejected" when the chassis' engine starter is engaged and the recept"Ic shalt be w-ircd to any 120 volt A/C
equipment requiring shore power. Location shall be: Drivers Side forward of rear wheel Color shall be RED
18
LICENSE PLATE BRACKET FRAME
A Stonewell frame license plate bracket with LED light installed above the frame,shall be provided at the rear of
the apparatus and shall be located on the driver side rear of the body,unless otherwise arranged.
TAIL.TURN,BACKUP ASSEMBLY LIGHTS
Two(2) Whelen #M6 Series tail-stop-turn-backup light assemblies shall be provided. and installed. The lights
shall be mounted in chrome four(4) bezel housing and installed at rear of the body. The following lights shall
be provided:
a) (2) Red warning lights
b) (2)Red tail and stop lights
c) (2) Amber turn signals
d) (2)Back-up lights
CEILING LIGHTS TecNiq E -CAV BODY
Six (6) TecNiq Model E32-1-000-1, 14" x 3.5" diameter LED lights shall be mounted to the body ceiling with
auto-on function. The light.%shall be mounted(2)on each side- Driver.Passenger, Rear.
CEILING LIGHTSTecNiq-CAV BODY
Six (6) TccNiq Model E18, 4.55" x 2.75" diameter LED lights shall be mounted to the main body side doors
ceiling with auto-on function. The lights shall be mounted(2)on each side- Driver, Passenger, Rear.
T.I.C. RECHARGING BRACKET
RR will ship hracket for SWB to install Upper shelf pmsenger side Location TBD
PORTABLE HANDLIGIIT X3
One(1) Stream light "Vulcan 180"LED portable hand light shall be installed including mounting bracket, with
120 volt charger wired to the specified shore power receptacle circuit allowing the light to recharge when not in
use. LOCATION TBD.Color Yellow
Two(2)Stream light"SL90 LED portable hand light shall be installed including mourning bracket, with 120 volt
charger wired to the specified shore power receptacle circuit allowing the light to recharge when not in use.
Location Rear Cabinet Color Yellow
Location CAV Body TBD Color Yellow
19
GROUND LIGHT
A TecNiy E10, 12 volt ground light shall be installed with mounting bracket wired to switch control in cib.
There shall be four(4)lights,2 at the mid CAB 2 at the rear of the CAV body.
SCENE LIGHTS
"I wo(2)Whelen M6 Series Model# M6ZC 4-5/16"x 6-3/4"scene lights with two(2)#M6P 15C chrome flanges
shall be provided. The warning light shall incorporate Linear Super-LED and Smart LED technology. The light
head configuration shall consist of 12 white Super-LEDs and a clear optic polycarbonate lens. The light head
shall be surface mountable via two screws. The mounting flanges shall be designed for 15 degree angled direction
for increased downward lighting. Location shall be: Rear body at the top
COMPARTMENT LIGHT SWITCHES
The exterior compartment lights shall be automatically controlled by a door activated"On-Off' switch.
OPEN DOOR WARNING,NO Audible Warning
RADIOS
SWB to Purchase Radio equipment see Quute 845917 and 948592
PURCHASE AND INSTALLATION - RADIO ANTENNA
Two (2) radio antenna shall be purchasde and installed by SWB on the apparatus at a location to be
determined by the Purchaser.
RADIO SPEAKER
Four(4)fire radio speaker,purchased and installed by SWB. Location shall be: TBA
RADIO INSTALLATION
Two(2) fire radio shall be purchased and installed SWB. Location will be center console
RADIO REMOTE HEAD
Two(2) fire radio remote heads shall be purchased and installed by SWR in rear command pack.
Price includes radio cable not to exceed 25 feet.
20
HEADSETS
Pour(4) Headsets purchased and iltstall, 2 in CAB,2 in REAR CP
Setcom, Estimate #948592, Date 1-25-2024
BACK-UP RM
The vehicle shall be provided with a Whelen model#WBUA112 automatic 97dB (decibel rating)back-up alarm
that shall activate automatically whenever the vehicle's transmission is placed into reverse gear. There shall be no
back-up alarm cut-off switch, in violation of safety regulations.
REINSTALL OEM BACK UP CAMERA
The Onginal OEM back up camera shall be re-mounted in the body of the Stonewell apparatus. Stonewell shall
manufacture a bracket to hold the camera and locate the assembly in a location most suited to providing an
unobstructed view. All OEM cables shall be reused.
H.EADLIGH'r FLASHER
One(1) Whelen#UHF2150A alternating headlight flasher shall be provided.
Simmn,Electronic,Whelen#C('SRN15 CENCOM
ELECTRONIC SIREN
Whelen Model CCSRNT5 -CEN-COM Carbide, self contained electronic siren shalt be provided. The 100/200
watt, eith (8) function siren shall have hands-free operation with public address and radio re-broadcast features.
The siren shall have the following tones: wail, yelp, mechanical, hi-low, yelp-249, whoop/warble (Power call
type tone),and air horn. The siren shall be able to operate in dual or mono modes. The OBDII port plug shall he
included.
The TA module shall be capable of controlling traffic advisors.
The unit shall have solid-state over/under voltage shutdown and output short circuit protection. The dip switches
located on the amplifier shall allow the user to change siren tone configurations. A list of the tone configurations
shall be pro%ided in the installation guide. The dual remote amplifier shall operate two(2) 100-watt speakers.
The siren shall have a face plate with green LEI)backlighting for easy control selection and visibility. The siren
shall have a removable unidirectional microphone with a 'push to talk' function that shall override all siren
functions.
SiREN SPEAKERS
Two(2)Whrlon Model#SA314P,Projector Serioa eiren apoukcra ahall bo pr rvidrd-ith SADKT9 Urackcta. Thi
loo-watt sitrn spcakcra shall be designed in a bt wk nylon composite housing with 122 decibel rating. i-tication
shall be:
21
LIGHTBAR
A Whelen Model Liberty#IX2-RRRR low profile Super-LED NFPA lightbar shall be installed. The 54" lightbar
shall be designed to meet the minimum clearing requirements for Zone A Upper. The internal components of the
lightbar shall be housed within a two piece extruded aluminum base/top. The outer shell shall be clear optic
polycarbonate lenses designed to maximize light output and shield against environmental elements.
The solid state 1/0 board shall be microprocessor controlled. The 1/0 board shall have built-in reverse-polarity
protection and output-short protection. The board shall have the ability to flash sixteen(16)LED warning lights.
There shall be a data bank of 13 Scan-Lock flash patterns including steady burn. The board shall also have outputs
to add takedown and alley lights. Low power and cruise light function shall also be included. The cruise light
function shall allow the user to employ the four(4)corner modules as marker courtesy lights.
ZONE A— UPPER—TRAFFIC Ll HT CONTROL
One(1)Opticom trat}ic light emitter system and control device shall be installed as specified in the lightbar
ZONE A— LOWER FRONT WARNiN , LIGHTS
Two(2)Whelen M6 Series Model 4M6R 4-5/16" x 6-3/4" warning lights and a M6FC chrome flange shall be in
the front lower area of cab. The warning lights shall incorporate Linear Super-LED and Smart LED technology.
The light heads configuration shall consist of 18 red Super-LEDs and a red optic polycarbonate lens. The light
heads shall be surface mountable via two screws. The light heads shall utilize an optic collimator and a chrome
vacuum metalized reflector for maximum illumination. The light heads shall include 164 flash patterns including;
a variety of CA Title 13 compliant,syncable, leftlrighL top/botiont, in/out,and steady burn.
`LONE B AND D— iNTERSECI-ION LIGHTS
Two (2) Whelen M4 Series warning red lights shall be installed. The warning lights shall be installed in lower
front bumper or crab fenders, one(1) each side, as far forward as possible. The warning lights shall incorporate
Linear-Super LED and Smart LED technology. The light head shall have six(6)red Super-LEDs with a red non-
optic polycarbonate lens for maximum light spread. The light head assembly shall have internal flasher eleven
(l 1)Sean-Lock flash patterns,including steady bran and synchronize power functions.
'LONE B AND D—CAB STEP LIGHTS
Warning Lights.Whelen Tracer Series.5 Segments,On Running Boards- LED
ZONE B AND D—LOWER MID AND RFAR BODY WARNING LiGHTS
Four(4)Whelen ION Red Warning lights. side hndy warning lights shall he.mnunted forward of the rear whew
well and rear enrner,,fthe,tx,dy w46 a chromo flange.The providod warning light shall incorporate Limas f3uper-
LEDIa and Smart LEDI) technology. The lighthead configuration shall consist of 18 clear Super-I.EDs and a
clear optic polycarbonate lens. The warning light,with the aid of two screws,shall have the ability to be installed
22
as a surface mount warning light. The light head shall utilize optic collimators and a metalized reflector for
maximum illumination.
Yom( NE HAND D— UPPER-OF BODY WARNING LIGHTS
Tracer 75"7 Segments per side R W R
ZONE C--UPPER OF BODY W 4RNING LIGHTS
Two(2) Whelen Rota Lights mounted on the upper body in the rear. One Blue one Red opposite of the lower
emergency lights.
ZONE C—CQNiMAND .REE1 LIGHTS
4 Ions added to rear two on body two on door. The light bar will have green side lights tied in to augment
Z0NI. C--SEGMENT(8) HEAD TRAFFIC ADVISOR-SOUND-OFF-SIGNAL X 2
Eight(8)Sound Off Signal light heads and bessels shall be mounted to the top of the rear doer. RIA
Eight(8)Sound Off Signal light heads and bessels shall be mounted to the bottom of the rear door. A
The Top row will be two color red, amber
The bottom will be amber only
Phis arrangement of light heads can be controlled via the Whelen Cencom siren to create flash patters such as
sweeping left, sweeping right, full-on for backing up visibility,alternating flashing, Emergency and many more.
In this configuration, the lights will be visible while the door is in the open or closed.
REFRIDGERATOR FREEZER
Victron 2000 Requested by RobertICECO VL 75 Pro D Heavy Duty Delos With possible Slide out TBD
COFFEE MAKER ANll CARAFE
Avantco Automatic:Coffee Makers
SWB to purchase and install per attached information.
Choice 64 oz. Insulated Themial Coffee Carafe: Server with Regular and Decaf Brew Thru Lids- 7" x 6 3/8"
120 VOLT STRAIGHT BLADE RECEPTACLES
Four(4) 120-volt 20-arut,att aight t,ladc i—vitw1us with apt inn loaded wentherproorcover shall be provided with
whing to the circuit breaker panel. 1 he receptacles shall be located:
23
FIXED wCVCH
Winch,Warn,fixed 10,000 Synthetic Rape
A Warn Winch Company 10,000-pound capacity 12-volt electric s. The winch shall be attached to the front
bumper. Power shall be supplied through a 12-volt pigtail .
With remote control.
BODV PAINTING SPECIFICATIONS ROOF EXCLUDED
In preparation for painting, the body will be DA sanded and care will be taken to remove any reasonable surface
blemishes,scratches,divots or marks that may vpcar post painting. Additionally, any surface marks that are not
satisfactorily removed through DA sanding will be tilled with automotive body filler to enhance surface
preparation and post painting appearance.
The driver and passenger sides of the body shall be painted,as follows:
Manufacturer: PPG
Materials:
a) F3963 Pigmented wash primer
b) F3970 Urethane Primer
c) Delfleet Evolution FBCH Polyurethane Basecoat
d) Delfleet Evolution Urethane Clear
e) Delfleet Evolution FBC is a Polyurethane 3.5 VOC Basecoat designed to produce ultimate durability with the
wet look appearance. The clear coat is a premium-quality urethane. The clear coat offers gloss and durability
features.
t)The body shall be wet sanded,buffed and polished.
g) One colors: Chevy Red Same as CAB
Front Bumper,Back Bumper,Cab steps also painted same RED, REAR Dever also red.
FRONT BUMPER—CHEVRON STRIPING
The front bumper surface shall have 3M 6"wide reflective red and yellow green striping installed. The Chevron
style stripe shall be applied at a 45-degree angle,pointing towards the center.Approximately 12"of striping shall
be applied on the driver and passenger side corners.
24
REAR BODY—CON STRIPING
50% of rear body surfaces shall have 3M Scotch lite Diamond Grade 6" wide reflective red and Yellow Green
striping installed. The Chevron style stripe shall be applied at a 45-degree angle, pointing towards the'center
upper portion of the rear apparatus. REA
MOUNTIN ' HARD W RF NtiiTc atvr� gOLT�
All mounting hardware shall be supplied by Stonewell.
Market Price Adjustmettt
SHIPPING WILL BE HANDLED BY ROUND ROCK FD
25